UL 1598B-2010 pdf download.Supplemental Requirements for Luminaire Reector Kits for Installation on Previously Installed Fluorescent Luminaires..
2 General 2.1 Components 2.1.1 Except as indicated in 2.1.2, a component of a product covered by this standard shall comply with the requirements for that component. See Appendix A for a list of standards covering components used in the products covered by this standard. 2.1.2 A component is not required to comply with a specic requirement that: a) Involves a feature or characteristic not required in the application of the component in the product covered by this standard, or b) Is superseded by a requirement in this standard. 2.1.3 A component shall be used in accordance with its rating established for the intended conditions of use. 2.1.4 Specic components are incomplete in construction features or restricted in performance capabilities. Such components are intended for use only under limited conditions, such as certain temperatures not exceeding specied limits, and shall be used only under those specic conditions. 2.2 Units of measurement 2.2.1 Values stated without parentheses are the requirement. Values in parentheses are explanatory or approximate information. 2.3 Undated references 2.3.1 Any undated reference to a code or standard appearing in the requirements of this standard shall be interpreted as referring to the latest edition of that code or standard.
3.4 A reector shall be secured in place by brackets, horizontal overlapping anges, screws, or equivalent mechanical means. Friction shall not be relied upon to secure the reector in place. The securement means shall be such that it will withstand any unintentional contact that occurs during lamp replacement. 4 Polymeric Materials 4.1 A polymeric material serving to complete the enclosure required in Enclosures, Subsection 5.3, of UL 1598, or providing structural support of any electrical component or of any non-electrical component weighing more than 3 ounces (85 g) shall comply with the requirements in Polymeric materials, Subsection 5.7, of UL 1598. 4.1 revised April 26, 2005 4.2 A metallized polymeric reector that is spaced within 3 inches (76.2 mm) from any lampholder, lamp contact, lampholder lead, wiring, or other electrical component (excluding the uorescent lamps) that are below the metallized surface shall comply with the applicable requirements for metallized plastic parts in Polymeric Materials – Use in Electrical Equipment Evaluations, UL 746C. 4.2 revised August 22, 2002 5 Air-Handling Luminaire Reectors 5.1 A reector kit intended for installation in a luminaire used as an air handling register shall not impede the intended air ow. 5.2 A nonmetallic material, adhesive, or adhesive tape used in a reector kit intended for installation in a luminaire used as an air handling register shall comply with Air-handling luminaires, Subsection 12.2, of UL 1598. 5.2 revised April 26, 2005 6 Adhesives 6.1 An adhesive or adhesive tape shall not be relied upon to secure any part to a panel, bracket, or component of a luminaire.
10 Lampholders 10.1 Installation of a Type II reector kit that involves relocation or removal of lampholders and lampholder leads originally supplied with the luminaire shall comply with the requirements in this section. 10.2 Replacement lampholders provided as a part of a reector kit shall be suitable for use with the type of uorescent lamp marked on the ballast involved. 10.3 After installation of a reector kit, lampholder connections shall comply with the requirements in Lampholders, Subsection 8.4, of UL 1598. 10.3 revised April 26, 2005 11 Wiring and Conductors 11.1 Supplemental wiring or connectors required for installation of the reector kit shall be included in the kit. The connectors shall be suitable for the number and size of conductors with which they are intended to be used. The supplemental wiring shall comply with the requirements in Electrical construction, Section 6, of UL 1598. 11.1 revised April 26, 2005 12 Ballasts 12.1 A replacement ballast shall be a Class P type and shall be suitable for use with the number and type of uorescent lamps to be installed in the luminaire after the reector kit installation.UL 1598B-2010 pdf download.